ROOFING APPLICATIONS

Direct-To-Deck

Foam-Control Direct-to-Deck is compatible with all major roofing materials and assemblies. Additional benefits such as design flexibility, resistance to moisture, and high R-value make Foam-Control roof insulation the preferred roofing solution.

  • Steel Deck: Minimum 22 gauge, 1/2″ deep, non-perforated, amd maximum 6″ flutes.
  • Thickness: Refers to ESR-1006 or UL Roof Desk Construction No. 458 for various thickness and Types.
  • Accepted Membranes: Approved EPDM or thermoplastic single-ply that are Ballasted, Mechanically Attached and fully-Adhered.
  • Cover Board (when requires): 1/4″ Dens-Deck or 1/2″ wood fiber board.

Direct-to-Deck

Flute Filler

Acts as the void filler and is designed to be installed over existing metal roofs. It provides a uniform and level substrate and is installed prior to the new roof system.

  • Lightweight with high strength
  • Improve R-value of roof assembly
  • No long-term R-value loss or thermal drift
  • No CFC, HCFC, HFC or formaldehyde
  • Superior moisture resistance

Flute Filler

Fanfold Roof Recover Board

Foam-Control® R-SHIELD® film-faced insulation is a cost-effective, durable, and energy efficient solution for cavity wall applications. It is an ideal material to provide a code compliant air and weather resistant barrier and reduce energy loss in brick faced residential and commercial masonry and framed walls.

Fanfold Roof Recover Board

Tapered Roofing

A cost-effective,d urable and energy efficient solution for roof insulation.
Foam-Control Tapered Roofing insulation provides the positive drainage necessary for commercial roofing systems. Foam-Control insulation is compatible with all major roofing
materials and assemblies.

  • No long-term R-value loss or thermal drift
  • No CFC, HCFC, HFC, or formaldehyde
  • No thermal barrier required
    (see ICC-ES ESR-1006 and UL ER11812-01)

Tapered Roofing Systems

Crickets

Foam-Control® precut crickets are a cost-effective, durable and energy efficient solution for roof insulation. Foam-Control crickets provide the positive drainage necessary for commercial roofing systems. Foam-Control crickets are compatible with all major roofing materials and assemblies.

EPS/Polyiso Assemblies

Foam-Control roof insulation is compatible with all commercially available Polyiso roof insulations. Slope to drain fabrication, design flexibility, and one step application make Foam-Control the preferred roofing solution for custom fabricated insulation among Contractors, Architects, and Engineers. Flat stock Foam-Control can be used to increase R-value at an economical cost.

  • Lower cost than Polyiso
  • Adds long-term R-value
  • Provides economical one step tapered roof system
  • Custom crickets and saddles are fast to install
  • Environmentally responsible
  • Superior moisture resistance

Polyiso Roof Assemblies

Holey Board

Cost effective thermal design is among the highest priorities in construction. Foam-Control insulation products are available in a range of densities necessary to provide energy efficiency, structural integrity, and cost effectiveness. They are proven to lower energy costs, saving both money and precious resources.

  • Lightweight with high strength
  • Excellent adhesion to concrete
  • No long-term R-value loss or thermal drift
  • No CFC, HCFC, HFC, or formaldehyde
  • Superior moisture resistance

Holey Board

Faced roof insulation

Compatible with Single-Ply roofing assemblies. Additional benefits such as design flexibility, moisture resistance, and high R-value make Foam-Control faced roof insulation the preferred roofing solution among Contractors, Architects and Engineers. It’s one of the most cost-effective steel deck roofing insulations on the market.

  • UL recognizes Foam-Control to be applied directly over steel roof decks along with a Class A, B or C roof covering.
  • Steel Deck: Minimum 22 gauge, 1/2” deep, non-perforated, and maximum 6” flutes.
  • Thickness: Up to 10″ (Type I). Refer to UL Roof Deck Construction No. 458 for other thickness and Types.
  • Accepted Membranes: Approved EPDM or thermoplastic single-ply that are ballasted or mechanically attached, maximum 80 mils thickness.

Faced Roof Insulations

LIBRARY

ADDITIONAL RESOURCES

Key Resources